Parts › PartFinder › Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) › Operator manual
Kaivac · Cleaning machine
Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual
COVER
NO-TOUCH CLEANING® (NTC) OPERATOR & PARTS MANUAL
P/N: MANUALNTC
www.kaivac.com
©2020 Kaivac, Inc. All rights reserved
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 1, used with permission. SES ref PF-7URA-UCZ7
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 1 of 38
REVISION SHEET
Revision Sheet for MANUALNTC
In short This page lists the release history of the manual. Only Release 1, dated 02/27/20, is recorded, as the initial design/release.
| Release No. | Date | Revision Description |
|---|---|---|
| 1 | 02/27/20 | Initial design/release of MANUALNTC |
NOTE: Specifications and parts are subject to change without notice
Kaivac, Inc.
2680 Van Hook Ave.
Hamilton, OH 45015
www.kaivac.com
©2020 Kaivac, Inc. All Rights Reserved
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 3, used with permission. SES ref PF-2DSP-EAAN
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 3 of 38
TABLE OF CONTENTS
Operator & Parts Manual - Table Of Contents
In short This table of contents lists the five sections of the manual (Getting Started, Assembly, Maintenance, Troubleshooting and Upkeep, and Parts Diagrams and Specifications) with the page number of each topic.
1.0 Getting Started
| No. | Topic | Page |
|---|---|---|
| 1.1 | Product Identification | 5 |
| 1.2 | Warranty Registration | 5 |
| 1.3 | Safety Precautions: Corded Units Only | 6 |
| 1.3 | Safety Precautions: Corded (Continued) | 7 |
| 1.3 | Safety Precautions: Corded (Continued) | 8 |
| 1.4 | Safety Precautions: Battery Units Only | 9 |
| 1.4 | Safety Precautions: Battery Operated (Continued) | 10 |
| 1.5 | Battery Information | 11 |
| 1.6 | Limited Warranty Protection Plan | 12 |
2.0 Assembly
| No. | Topic | Page |
|---|---|---|
| 2.1 | Tool Arrangement | 13 |
| 2.2 | Preparation For Use | 14 |
3.0 Maintenance
| No. | Topic | Page |
|---|---|---|
| 3.1 | Battery Use | 15 |
| 3.2 | Machine Maintenance | 16 |
| 3.3 | Vacuum Diagram | 17 |
| 3.4 | Pump Diagram | 18 |
| 3.5 | 1200 Electrical Diagram | 19 |
| 3.6 | AC Electrical Diagram | 20 |
| 3.7 | QC Power Pack Electrical Diagram | 21 |
4.0 Troubleshooting and Upkeep
| No. | Topic | Page |
|---|---|---|
| 4.1 | Troubleshooting | 22 |
| 4.2 | Troubleshooting (Continued) | 23 |
| 4.3 | Troubleshooting (Continued) | 24 |
| 4.4 | Troubleshooting Tips | 25 |
| 4.5 | Replacement (Monthly) | 25 |
5.0 Parts Diagrams and Specifications
| No. | Topic | Page |
|---|---|---|
| 5.1 | 1200 Vac Tank Assembly | 26 |
| 5.2 | 1200 Water Tank Assembly | 26 |
| 5.3 | 1250 Black Box Assembly | 27 |
| 5.4 | 1200 Switch Panel Assembly | 28 |
| 5.5 | 1200 Valve Assembly | 28 |
| 5.6 | 1250 Pump Assembly | 29 |
| 5.7 | 1200 Vac Motor Assembly | 29 |
| 5.8 | 1700/17001 Vac Tank Assembly | 30 |
| 5.9 | 1700/17001 Water Tank Assembly | 30 |
| 5.10 | 1750/17501 Pump Assembly | 31 |
| 5.11 | 1700/17001 Vac Motor Assembly | 31 |
| 5.12 | 27001 Vac Tank Assembly | 32 |
| 5.13 | 27001 Water Tank Assembly | 32 |
| 5.14 | 27501 Pump Assembly | 33 |
| 5.15 | 27001 Vac Motor Assembly | 33 |
| 5.16 | 1750/17501/27501 AC Black Box Assembly | 34 |
| 5.17 | QC Power Pack Assembly | 35 |
| 5.18 | 1700/17001 Switch Panel Assembly | 36 |
| 5.19 | 27001 Switch Panel Assembly | 36 |
| 5.20 | 1700/17001/27001 Valve Assembly | 37 |
| 5.21 | HEPA Assembly | 37 |
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 4, used with permission. SES ref PF-YKYH-QOVJ
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 4 of 38
1.0 Getting Started
1.1 Product Identification
In short This section helps you find the manual pages that match your system: 1200 Series, 1700 Series or 2700 Series (NTC). Compare your machine with the drawings and go to the pages listed for it.
Identify your system below to see the correct manual pages for your product.
1200 Series (NTC)
Associated Pages:
pg. 19
pg. 26-29
pg. 37
1700 Series (NTC)
Associated Pages:
pg. 20,21
pg. 30-31
pg. 34-37
2700 Series (NTC)
Associated Pages:
pg. 20,21
pg. 32-37
1.2 Warranty Registration
In short Register your Kaivac product at kaivac.com/warranty. Registering confirms your warranty coverage and keeps you informed about updates.
Thank you for purchasing a Kaivac product. Please take a few moments to register your product at kaivac.com/warranty.
Why register?
- Ensure your warranty coverage
- Simplify warranty service in the future with your information on file
- Be the first to know about upgrades, issues, new options and special offers.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 5, used with permission. SES ref PF-DZU4-WFUN
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 5 of 38
1.0 Getting Started
1.3 Safety Precautions: Corded Units Only
In short This section lists the basic safety rules to read and follow before using the corded unit, to reduce the risk of fire, electric shock or injury. It also gives extra warnings for the spray system, which can produce 500 PSI (3447 kPa).
IMPORTANT SAFETY INSTRUCTIONS — SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING: To reduce the risk of fire, electric shock, or injury:
- Turn off the unit before unplugging. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
- Connect to a properly grounded outlet only. Do not remove ground pin. See Grounding Instructions below.
- DO NOT allow to be used as a toy. Close attention is necessary when used by or near children.
- Use only as described in this manual. Use only manufacturer’s recommended attachments.
- Inspect cord prior to use. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors or dropped into water, return it to a service center.
- DO NOT handle plug or appliance with wet hands.
- DO NOT pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
- DO NOT unplug by pulling on cord. To unplug, grasp the plug, not the cord.
- DO NOT put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
- Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. Turn off all controls before unplugging.
- Use extra care when cleaning on stairs.
- DO NOT use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
- DO NOT pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
- If using extension cord with appliance, make sure the connection is above the floor and away from exposure to liquid.
- Keep all connections dry and off the ground.
- To reduce the risk of injury, close supervision is necessary when a product is used near children.
- Stay alert - watch what you are doing.
- Keep operating area clear of all persons.
- The Kaivac shall be disconnected from mains during cleaning or maintenance and when replacing parts or converting the machine to another function.
- DO NOT overreach or stand on unstable support. Keep good footing and balance at all times.
- DO NOT operate without the float installed. If float is removed, reinstall by screwing back into place.
- Keep the cord away from heated surfaces.
- DO NOT use without dust bag and/or filters in place.
- This product comes with a grounded attachable extension cord. If damaged, replace with equivalent cord. This cord must be attached and mechanically secured using the provided cord connector to use the equipment.
- DO NOT operate the product when fatigued or under the influence of alcohol or drugs.
- Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.
- Follow the maintenance instructions specified in the manual.
SPRAY SYSTEM WARNINGS (ONLY):
- DO NOT spray liquid from the Kaivac onto electrical outlets or any electrical devices.
- Risk of injection or injury to persons - DO NOT direct discharge stream at persons.
- INJECTION HAZARD: Equipment can cause serious injury if the spray permeates the skin. Do not point the gun at anyone or any part of the body. In case of permeation, seek medical aid immediately.
- THIS SYSTEM IS CAPABLE OF PRODUCING 500 PSI (3447 kPa). To avoid rupture and injury, do not operate this pump with components rated less than 500 PSI (3447 kPa) working pressure (including but not limited to spray guns, hose, and hose connections); and before servicing, cleaning or removal of any part, shut off power and relieve pressure.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 6, used with permission. SES ref PF-6QOF-JRTE
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 6 of 38
1.0 Getting Started
1.3 Safety Precautions: Corded (Continued)
In short This page continues the corded safety precautions: keep the appliance away from children and untrained users, test the GFCI before each use, and plug into a properly grounded outlet. The machine is for indoor commercial use only and must be stored indoors.
- High pressure cleaners shall not be used by children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or untrained personnel. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- This product may also have been provided with a ground fault circuit interrupter built into the power cord. If replacement of the plug or cord is needed, use only identical replacement parts.
- Test the ground fault circuit interrupter (GFCI) before each use.
- Personal Protective Equipment (PPE): It is recommended to wear proper personal protective equipment as required by the chemical product label instructions used in conjunction with the appliance.
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION (for spray systems only)
This machine was supplied with a ground-fault circuit-interrupter(GFCI) built into the plug of the power-supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection.
This appliance is for use on a nominal circuit and has a grounding attachment plug. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adapter should be used with this appliance.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local DOE and ordinances.
WARNING Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet have a proper outlet installed by a qualified electrician.
FOR INDOOR USE ONLY
INTENDED FOR COMMERCIAL USE
WARNING — To Reduce the Risk of Electric Shock — Do not expose to rain. Store indoors.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 7, used with permission. SES ref PF-O4W2-GPCU
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 7 of 38
1.0 Getting Started
1.3 Safety Precautions: Corded (Continued)
Make sure your extension cord is in good condition and is the correct size for your appliance. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating.
Use only three-wire outdoor extension cords that have three-prong grounding receptacles that accept the appliance’s plug.
Warning — To reduce the risk of personal injury due to a loose electrical connection between the appliance’s plug and extension cord, firmly and fully attach the appliance plug to the extension cord. Periodically check the connection while operating to ensure it is fully attached. Do not use an extension cord that provides a loose connection. A loose connection may result in overheating, fire, and increases the risk of a burning.
To reduce the risk of disconnection of the appliance cord from the extension cord during operations:
- Make a knot as shown in Figure 1 below:
Figure 1 - Method of securing the appliance cord to the extension cord set
Table 1 - Minimum gauge for extension cords
| Ampere rating | Volts | Total length of cord | ||||
|---|---|---|---|---|---|---|
| More than, A | Not more than, A | 7.62 m (25 ft) | 15.24 m (50 ft) | 30.48 m (100 ft) | 45.72 m (150 ft) | |
| 120 V | mm² (AWG) | |||||
| 0 | 6 | — | 0.82 (18) | 1.3 (16) | 1.3 (16) | 2.1 (14) |
| 6 | 10 | — | 0.82 (18) | 1.3 (16) | 2.1 (14) | 3.3 (12) |
| 10 | 12 | — | 0.82 (18) | 1.3 (16) | 2.1 (14) | 3.3 (12) |
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 8, used with permission. SES ref PF-POU7-P4K7
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 8 of 38
1.0 Getting Started
1.4 Safety Precautions: Battery Units Only
In short This section lists the safety rules for battery-powered units, covering the battery, the charger and vacuum operation. Read all of it before using the appliance, and keep the instructions.
Batteries and chargers: make sure your charger is compatible with your batteries, and set its charging algorithm to your battery pack before you use it.
IMPORTANT SAFETY INSTRUCTIONS — SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING: To reduce the risk of fire, electric shock, or injury:
- ONLY USE with Kaivac, Inc. battery, and charger, CHARG36V series.
- When charging, make sure charger has at least 6 inches of clearance on all sides for adequate air flow.
- DO NOT charge batteries outdoors.
- DO NOT attempt to repair, service or modify the batteries or charger. Contact Kaivac Technical Support with any issues.
- DO NOT short-circuit the battery or charger terminals with conductive items such as paper clips. This can deliver high current, resulting in hear and fire.
- Keep sparks and flames away from batteries.
- DO NOT crush, drop, incinerate or damage the Battery. Do NOT use a Battery that has been damaged in any way. DO NOT incinerate the battery even if it is non-working or severely damaged. The battery can explode in a fire.
- DO NOT expose a Battery or appliance to fire or excessive temperature. Exposure to fire or temperature above 265ºF (130ºC) may cause explosion.
- DO NOT use or store the NTC System or Battery in wet or moist conditions, or near flammable or combustible materials.
- DO NOT charge or store Battery for extended time (1 month or more) in temperatures below 40ºF (4ºC).
- If fumes smelled from battery, discontinue use immediately, place inside a metal canister in a well-ventilated area.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery, picking up or carrying the appliance. Carrying the appliance with your finger on the switch, or energizing an appliance that has the switch on invites accidents.
- Disconnect the battery from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
- When battery is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Charger/Electrical Warnings:
- For commercial or residential use.
- Connect charging cord to a properly grounded outlet only. See Grounding Instructions.
- DO NOT plug in Charger while Vacuum Head is in ON position. It may damage the system.
- Follow all charging instructions and do not charge the battery or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
- DO NOT leave charger plugged in when not in use.
- DO NOT operate charger if it has received a sharp blow, been dropped, or damaged in any way.
- DO NOT use charger if it has a damaged cord or plug. DO NOT carry charger by cord.
- DO NOT pull on charger cord to unplug. Grasp and pull the plug, not the cord.
- DO NOT handle charger, including charger plug and charger terminals, with wet hands while charger is plugged in or while inserting plug into electrical outlet.
Vacuum and operation warnings:
- NO COMBUSTIBLES! Sparks inside the motor can ignite flammable vapors or dust. Do not use near combustible liquids and gases, or to pick up explosive dusts or gasoline. Do not pick up anything that is burning or smoking such as cigarettes or hot ashes.
- DO NOT plug Battery in while Vacuum Motor is in ON position. It may damage the system.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 9, used with permission. SES ref PF-4ZWN-D4NL
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 9 of 38
1.0 Getting Started
1.4 Safety Precautions: Battery Operated (Continued)
- CHECK FLOAT on Vacuum Motor and clean before each use. Clogged screen may lead to loss of suction.
- DO NOT allow to be used as a toy. Close attention is necessary when used by or near children.
- Use only as described in this manual. Use only manufacturer’s recommended attachments.
- DO NOT put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.
- Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
- Use extra care when cleaning on stairs.
- DO NOT use without Vacuum Motor Float Cage in place.
SPRAY SYSTEM WARNINGS (ONLY):
- Do not spray liquid from the Kaivac onto electrical outlets or any electrical devices.
- Risk of injection or injury to persons - do not direct discharge stream at persons.
- INJECTION HAZARD: Equipment can cause serious injury if the spray permeates the skin. Do not point the gun at anyone or any part of the body. In case of permeation, seek medical aid immediately.
- This system is capable of producing 500 PSI (3447 kPa). To avoid rupture and injury, do not operate this pump with components rated less than 500 PSI (3447 kPa) working pressure (including but not limited to spray guns, hose, and hose connections); and before servicing, cleaning or removal of any part, shut off power and relieve pressure.
- High pressure cleaners shall not be used by children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or untrained personnel. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
This product comes with a grounded attachable extension cord. If damaged, replace with equivalent cord rated 120V, 15 amps, 3-wire, 14 GA. This cord must be attached and mechanically secured using the provided cord connector to use the equipment.
QUICK RELEASE INSTRUCTIONS
In short These instructions explain how to disconnect the motor from the battery, remove the battery from the unit, and reconnect it. The connector is turned 90 degrees to release or lock it.
- To disconnect the motor from the Battery, pull the button on the electrical connector toward you and turn the electrical connector counter-clockwise 90 degrees to disengage the motor electrical cord from the Battery Pack.
- Then to remove the Battery from the unit, while standing at the rear of the nit, grab the Battery on either side and pull it away from the unit.
- To reconnect the Battery Pack to the electrical motor, insert the motor electrical connector into the Battery Pack outlet aligning the key features of the electrical connector into the outlet key-way. Press the connector into the outlet and turn clockwise 90 degrees until the connector locks into place.
GROUNDING INSTRUCTIONS
In short The charger and appliance must be grounded by plugging into a properly installed, grounded outlet. Do not modify the plug or use an adapter, and wear the PPE required by the chemical product label.
Batteries and chargers: make sure your charger is compatible with your batteries, and set its charging algorithm to your battery pack before you use it.
The charger must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having equipment grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING — Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet; have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal circuit and has a grounding attachment plug. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adapter should be used with this appliance.
Personal Protective Equipment (PPE): It is recommended to wear proper personal protective equipment as required by the Chemical product label instructions used in conjunction with the appliance.
WARNING — To Reduce the Risk of Electric Shock — Do not expose to rain. Store indoors.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 10, used with permission. SES ref PF-LSZQ-XLXW
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 10 of 38
1.0 Getting Started
1.5 Battery Information
In short This section explains how to care for the Kaivac lithium-ion battery: store it at room temperature, expect capacity to fade over time, and recycle it properly when its life ends. It also lists the battery, charger and storage specifications.
Batteries and chargers: make sure your charger is compatible with your batteries, and set its charging algorithm to your battery pack before you use it.
Keep Batteries at Room Temperature: That means storing between 32 and 80 degrees F (0ºC to 27ºC). The worst thing that can happen to a lithium-ion Battery is to have it exposed to elevated temperatures.
Batteries Lose Capacity Over Time: Batteries naturally deteriorate over time whether being used or not. Batteries deteriorate at a rate of 10% run time per year.
Fully Discharge vs. Partial Discharge and the Effect on Battery Cycles: Unlike lead acid batteries typically used in auto scrubber, the Kaivac Battery is not damaged by fully discharging. The BMS (Battery Management System) has a cutoff voltage of 30V which protects the Battery from experiencing full discharge. Running the Battery to full discharge will reduce the amount of charge cycles. The expected hours of use are approximately 600 hours. For example, if running to full discharge, you would expect 400 cycles. If you run to 80% discharge, then you would expect to get more cycles (500 cycles).
Extended Storage: It is recommended to discharge to 40% capacity (35V) and store in a cool location (between 32ºF to 80ºF or 0ºC to 27ºC). Hour
Battery Gauge: The Kaivac Batteries come with a built-in Battery Gauge or “Fuel Gauge” which shows the approximate run time remaining.
Disposal: Properly dispose of Battery at a local recycling location.
| Battery Specifications | |
|---|---|
| Weight | With Box, 11 lbs. (4,9 kg) |
| Body Material | Injection Mold Polypropylene |
| Dimensions (H x W x D) | 18 x 7 x 5 in. (45,7 x 17,8 x 12,7 cm) |
| Voltage | 36V DC |
| Battery Capacity | 15 A-hr |
| Battery Current | 15 A DC |
| Battery Type | Lithium-Ion |
| Approx. Run Time BOL (Beginning of Life) | 60 minutes |
| Approx. Run Time EOL (End of Life) | 35 minutes (discontinue use and take to recycling center) |
| Battery Box Receptacle | IP65 / IP67 (not required for UL) |
| Run Time Hour Meter | Acts as “odometer for battery” and runs only when motor switch is ON |
| Approx. Charge Cycles | 400 @ 100% discharge / 500 @ 80% discharge |
| Cut off Voltage (fully discharged) | 30V |
| Charger Specifications | |
| Approx. Charge Time | 5.5 hours |
| Charger Amps | 4 Amps |
| Charge Voltage | 42V DC |
| Charger Voltage | 110-240VAC / 36VDC (240VAC version only needs correct plug for wall outlet) |
| Charging Robustness | No special instructions |
| Battery Charge Memory | None |
| Battery Charge Gauge | Yes, LED Indicator |
| Approx. Charge Cycles | 400 @ 100% discharge / 500 @ 80% discharge |
| Storage/Inventory: | |
| Storage & Operation Ambient Temp | 32ºF (0ºC) to 80ºF(27ºC) |
| Storage & Shipping Charge | 40-60% Charge (35-38VDC) |
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 11, used with permission. SES ref PF-IOOI-PM6T
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 11 of 38
1.0 Getting Started
1.6 Limited Warranty Protection Plan
In short This section explains what Kaivac covers for defects in workmanship or materials and for how long. Coverage depends on the chemicals used, and warranty claims need a Return Authorization Number (RAN) obtained from Kaivac Customer Service.
The Kaivac has been engineered and tested to provide long lasting performance. This warranty covers defects in workmanship or materials under normal use and service from the date of purchase.
Kaivac, Inc. warrants the following components to be free from defects in materials and workmanship for these time periods:
- Extended Warranty for end users who use only Kaivac chemicals for the life of the machine.
- 5 years on rotationally molded parts
- 3 years on other parts (excluding wear items)
- 1 year on labor
- Standard Warranty (for approved non-Kaivac chemicals)
- 1 year parts and labor
- Chemicals that have not been approved by Kaivac (If uncertain, please contact Kaivac to verify your chemical before using).
- No warranty
All Kaivac replacement parts are guaranteed for 90 days from the date of installation. Normal wear items such as wheels, hoses, seals, gaskets, cords, casters, squeegees and GFCI are excluded from warranty coverage.
All warranty claims must be accompanied by a Return Authorization Number (RAN), which is available by calling the Kaivac, Inc. Customer Service Department. No returns will be accepted without a RAN.
This warranty does not apply to return freight costs, damage or defect caused by accident, negligence, misuse, fire or repair done by anyone other than a Kaivac authorized repair center. In no event shall Kaivac, Inc. be liable for incidental or consequential damages, or any damages to persons or property.
Please Note: Under no circumstances will the seller be liable for any loss, damage, expenses or consequential damages arising in connection with the use or inability to use seller’s product. Kaivac, Inc. reserves the right to make changes or improvements to its equipment without notice. Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty is in lieu of any other warranty expressed or implied, including any warranty of merchantability or fitness for a particular purpose.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 12, used with permission. SES ref PF-574S-RGVP
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 12 of 38
ASSEMBLY
2.0 Assembly
2.1 Tool Arrangement
In short This section shows where each tool and hose is stored on the machine. There are separate drawings for the 1200 and for the 1700 and 2700 models.
1200 Tool Arrangement
1700 and 2700 Tool Arrangement
Vac Hose: *1700 Series: (VH25)(HC5)(VHST20); *2700 Series: (VH40)(HC5)(VHKVJRST)
Pressure Hose: *1700 Series: (PH45); *2700 Series: (PH75B)
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 13, used with permission. SES ref PF-JYDB-Y24O
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 13 of 38
2.0 Assembly
2.2 Preparation For Use
In short This section lists the six checks to make before cleaning: fill the machine with water, set up the chemical line and metering tip, confirm tools and supplies, and use a foam inhibitor if needed. Then inspect the hoses and spray lines and test the GFCI after plugging in.
- Fill machine with clean, cool water.
- Prepare the cleaning solution you will be using by attaching the chemical feed line and cap to the top of your chemical bottle. Then select the proper metering tip. (See placard for metering tip information)
- Check machine for all tools and supplies needed to complete task. See Tool Arrangement in Section 2.2 of this manual.
- If using a cleaning product that foams, use a foam inhibitor to cut excess. Pour 2 capfuls of inhibitor in the Vac Hose with Vac running to coat inside of Hose.
- Check all hoses and spray lines for damage prior to use. If damage is found, do not continue until proper repairs are completed.
- Plug in machine and test GFCI (Ground Fault Circuit Interrupter) to ensure it is working properly. You are now ready.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 14, used with permission. SES ref PF-52NA-6MJ4
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 14 of 38
3.0 Maintenance
3.1 Battery Use
In short This section shows where the Power Pack mounts on the bracket of the black box and how to lower it into place. It also shows where the charging port is and how to plug in and unplug the charger.
Batteries and chargers: make sure your charger is compatible with your batteries, and set its charging algorithm to your battery pack before you use it.
The bracket mounted on the black box is where the Power Pack is mounted.
Lower Power Pack onto bracket slide, lowering it down into place.
The Charging Port location for the Power Pack is pictured below.
Insert Charger into Charge Port as displayed below.
To unplug charger, press button and pull back on Charger cord.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 15, used with permission. SES ref PF-KD2K-MD2O
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 15 of 38
3.0 Maintenance
3.2 Machine Maintenance
In short This section lists what to check on each part of the machine: floor tool, spray gun, hoses, tanks, leaks, electrical system, vacuum wand and HEPA filter. Unplug the machine before lifting the electric cover assembly.
CAUTION: Always unplug machine before lifting electric cover assembly.
| ITEM | PROCEDURE |
|---|---|
| Floor Squeegee |
|
| Spray Gun |
|
| Pressure Hose |
|
| Water Tank |
|
| Vacuum Tank |
|
| Leaks |
|
| Electrical System |
|
| Vacuum Wand |
|
| HEPA Filter |
|
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 16, used with permission. SES ref PF-IDU5-QHWB
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 16 of 38
3.0 Maintenance
3.3 Vacuum Diagram
In short This page shows the path air takes through the vacuum system. Air enters at the vacuum wand, travels through the vacuum hose to the vacuum tank, then passes the float switch to the 3-stage vacuum and the HEPA filter before leaving through the exhaust.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 17, used with permission. SES ref PF-PIMS-NU25
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 17 of 38
3.0 Maintenance
3.4 Pump Diagram
In short This page shows a flow diagram of the pump system. It traces the path from the water tank, pump and unloader, through the chemical bottles, valve and injector, to the pressure hose, spray gun and spray nozzle.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 18, used with permission. SES ref PF-X2XQ-7A6N
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 18 of 38
3.0 Maintenance
3.5 1200 Electrical Diagram
In short This section gives the wiring diagrams for the AC-powered 1250 NTC machine (KV1250) and the AC-powered 1215 NTC machine (KV1215). Each diagram shows how the power cord, circuit breaker switches, hour meter, pump motor and vacuum motor are wired.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 19, used with permission. SES ref PF-K7KO-LKKJ
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 19 of 38
3.0 Maintenance
3.6 AC Electrical Diagrams
In short This page shows the wiring diagrams for AC-powered NTC machines (KV1750, KV2750). One diagram covers the standard machine and the other covers the machine with the Armor unit.
AC-POWERED NTC MACHINE (KV1750, KV2750)
AC-POWERED NTC MACHINE WITH ARMOR UNIT (KV1750, KV2750)
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 20, used with permission. SES ref PF-6VLR-WJEY
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 20 of 38
3.0 Maintenance
3.7 Quick Change Power Pack Electrical Diagram
In short This page shows the wiring diagram for the quick change power pack. It traces the 36V DC battery pack through the thumb-lock receptacle to the control panel, the pump motor and the vacuum motor.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 21, used with permission. SES ref PF-4G3A-XXUA
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 21 of 38
4.0 Troubleshooting and Upkeep
4.1 Troubleshooting
In short This table lists problems by area (electrical, vacuum system, blow dry system) with their possible causes and solutions. Always unplug the machine before lifting the electric cover assembly.
CAUTION: Always unplug machine before lifting electric cover assembly.
| AREA | PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|---|
| Electrical | No Power to pump or vac motor | Machine not plugged in | Plug machine in |
| Switch not “on” | Check switches for “on” | ||
| GFCI tripped | Test and reset GFCI | ||
| Building circuit overloaded | Check and reset circuit | ||
| Switch wires loose | Disconnect power and check for loose wire | ||
| Connections loose | Disconnect power and check for loose wire under panel | ||
| Electrical burning smell | Vac motor brushes worn | Remove vac motor and repair | |
| Vac motor hung up | Release pressure on hose and jog vac switch, or replace | ||
| Pump motor hung up | Release pressure on hose and jog pump switch, or replace | ||
| Vacuum System | No/Weak vacuum | Vac tank full | Empty vac tank |
| Squeegee blades or wheels worn | Replace wheels or blades and check periodically | ||
| Float shutoff screen dirty | Spray off float screen to clean | ||
| Float ball stuck | Tap float and release/clean | ||
| Damaged hose | Cut and repair/replace | ||
| Dump hose plug missing | Contact dealer and replace | ||
| Access lid not right | Tighten lid hand tight | ||
| Vacuum hose plugged | Flush hose to remove debris | ||
| Too much liquid in vac hose | Allow air in when vacuuming | ||
| Vac hose still wrapped | Unwrap vac hose fully | ||
| Exhaust plugged | Remove HEPA filter and clean | ||
| Leak in vac tank | If repairable, clean and dry affected area and seal with silicone | ||
| HEPA filter clogged | Remove HEPA filter and clean | ||
| Moisture from exhaust | Vac tank full | Dump vac tank | |
| Float shutoff missing | Replace | ||
| Excessive foam in vac tank | Use defoamer | ||
| Blow Dry System | No air flow | Hose disconnected | Reconnect hose |
| Moisture from exhaust | Water in blow hose | Dry blow line | |
| Suction, not blow action | Vacuum hose connected to vac tank | Reconnect to vac motor exhaust hose |
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 22, used with permission. SES ref PF-JBQQ-MISU
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 22 of 38
4.0 Troubleshooting and Upkeep
4.2 Troubleshooting
CAUTION: Always unplug machine before lifting electric cover assembly.
In short This table lists problems by machine area, with the possible causes and the solution for each. This page covers the High Pressure System (no water or low pressure, bad spray pattern) and the start of the Chemical Injection System (no chemical flow). Unplug the machine before lifting the electric cover assembly.
| AREA | PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|---|
| High Pressure System | No water from pump or low pressure | Out of water | Fill water tank |
| Gun nozzle plugged | Remove orifice with Allen wrench and clean | ||
| Air in pump (vapor lock) | Use power prime technique | ||
| Gun orifice missing | Replace orifice | ||
| Water tank filter plugged | Clean tank and filter | ||
| In-line bowl filter plugged | Remove filter cover and clean | ||
| Bowl filter lid loose | Gently tighten bowl cover | ||
| Pressure hose damaged | Repair or replace | ||
| Quick disconnect leaking | Tighten or replace | ||
| Injector plugged | Remove safety cap from chemical and blow small amounts of compressed air into line | ||
| Pulse hose damaged | Repair or replace | ||
| Regulator failed | Replace | ||
| Hose kinked | Unkink and check for damage | ||
| Seals in pump need replaced | Remove and replace seals | ||
| Bad fan pattern or pinpoint pattern on gun | Debris in nozzle | Remove orifice with Allen wrench and clean | |
| Orifice damaged | Remove and replace | ||
| Chemical Injection System | No chemical flow | Out of chemical | Refill chemical |
| Safety cap not secure | Check safety cap/tighten | ||
| Chemical valve “off” | Check on/off valve | ||
| Safety cap plugged | Replace cap | ||
| Spray gun in wrong mode | Make sure gun nozzle is pulled out away from gun chemical mode | ||
| Metering tip plugged | Check metering tip for clog | ||
| Injector plugged | Remove safety cap from chemical and blow small amounts of compressed air into line | ||
| Air entering system | Check for air entering system around chemical lines or injector | ||
| Injector installed backwards | If fluttering or pulsing sound can be heard while spraying or when machine is running, it is possible that your injector is in backwards. Remove; reinstall. | ||
| Kink in chemical line | Replace chemical line |
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 23, used with permission. SES ref PF-PW4F-L3YG
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 23 of 38
4.0 Troubleshooting and Upkeep
4.3 Troubleshooting
CAUTION: Always unplug machine before lifting electric cover assembly.
In short This chart lists problems by machine area, with the possible cause and the solution for each. This page continues the Chemical Injection System and covers the dump system, wheels and casters, and the squeegee head.
| AREA | PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|---|
| Chemical Injection System continued | Not enough chemical | Metering tip plugged | Remove and clean |
| Not enough chemical | Wrong metering tip | Check and replace per chart | |
| Chemical line blows off safety cap | Debris in injector | Remove safety cap from chemical and blow small amounts of compressed air into line | |
| Water back flows into chemical bottle | Bad seat on injector check valve | Check injector o-ring or replace | |
| Water back flows into chemical bottle | Bad safety cap | Replace safety cap | |
| Dump System | Dump hose will not empty tank | Dump hose cap not removed | Remove cap |
| Dump hose will not empty tank | Clog in bottom of tank | Tip dump contents, remove debris | |
| Dump hose leaks | Hose cut | If leak is less than 4” from tank side, cut and reattach, or replace | |
| Dump hose leaks | Clamp loose | Tighten hose clamp | |
| Dump hose leaks | Dump cap missing | Replace cap | |
| Wheels and Casters | Wheels will not roll; rubbing | Flat tires | Inflate tires to 30 p.s.i. |
| Wheels will not roll; rubbing | Debris wrapped around axle | Check for debris on axle | |
| Wheels will not roll; rubbing | Bearings tight | Grease bearings | |
| Wheels will not roll; rubbing | Wheels too loose on axle | Remove wheel, add washers to take up slack | |
| Wheels will not roll; rubbing | Bearings falling out | Replace bearing assembly | |
| Squeegee Head | Floor streaks | Worn blades or wheels | Replace wheels and/or blades |
| Squeegee head does not easily rotate when installed on wand | Brass ring on wand not in groove | Loosen coupling nut and re-position head on groove | |
| Squeegee head does not easily rotate when installed on wand | Coupling nut too tight | Loosen 1/2 turn | |
| Head will not stay on wand | Coupling nut cracked | Replace | |
| Head will not stay on wand | Brass ring worn | Replace | |
| Premature blade wear | Squeegee wheels worn | Check wheels for wear/replace | |
| Sucks to the floor too tightly | Squeegee wheels worn | Check wheels for wear/replace |
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 24, used with permission. SES ref PF-MROY-VNEZ
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 24 of 38
Troubleshooting and Upkeep
4.4 Troubleshooting Tips
In short This section lists what to check when vacuum pickup is poor or the vacuum shuts off early, such as the squeegee blades, float cage and vacuum hose. It also gives the phone numbers and email for Technical Support.
Poor Vacuum Pickup
- Check Squeegee Blades. If blades are worn or damaged, replace Squeegee Head.
- Clean float cage.
- Check for leaks in the Vacuum Hose or Gasket.
- Check for clogged Vacuum Hose.
- Check to see if float ball was tripped.
Vacuum Shuts Off Prematurely
- Check Float Cage; clean if dirty.
- Cleaning Chemicals may be producing too much foam. Use correct Chemicals.
Other Issues? Contact Technical Support
Phone:
United States and Canada: 1-800-287-1136
International: 1-513-887-4600
Email:
info@kaivac.com
For Technical Support Contact Form go to: https://www.kaivac.com/contactus.php and choose Technical Support tab.
4.5 Replacement (Monthly)
In short Monthly tasks keep the system performing well. Check the squeegee blades for wear, and replace the Vac Wand head every 6-8 weeks.
The following tasks should be performed monthly to keep your system operating at peak performance.
Check for worn squeegee blades. Worn blades cause streaking and loss of vacuum suction.
Unscrew cuff at end of Vac Wand, remove old head and replace with new every 6-8 weeks for optimal performance.
Source: Kaivac No-Touch Cleaning (NTC) Release 1 (02/2020) Operator Manual MANUALNTC_062520-1 Rev. Release 1, page 25, used with permission. SES ref PF-QEIM-FZGQ
No-Touch Cleaning (NTC) Release 1 (02/2020) MANUALNTC_062520-1 (Release 1)Page 25 of 38
Kaivac and KaiVac are trademarks of Kaivac, Inc. Southeastern Equipment & Supply is an independent dealer.
